The Aerocool Shark Blue Edition 120mm x 25mm fans are a great addition to any system. The fan comes with a Voltage reduction cable to allow operation @ 7V without a controller or external device. This allows a range of specs to be achieved with just one fan. The 15 blade design allows for higher air pressure and air flow! All the cables for the Shark Series are factory sleeved in black. Four Blue LEDs are built into the frame for added effect.

• Innovative Fluid Dynamic Bearing for longer life span, higher precision rotation, and anti-shock function.
• 15 fan blades generates High Air Pressure and Air Flow.
• Unique and Stylish "Shark Fin" Fan Blade design.
• Duo Mode Operation - The Shark fan operates in both "Power" mode (12V) and "Silence" mode (7V - with adaptation of Voltage Reduction Cable).
• All cables are sleeve wrapped in black.
• Blue Edition fan comes with clear Blue Blades with 4 Blue LEDs
• Black Edition fan comes with Glossy Black Blades without LED.

Standard Connection (Power mode)
Standard Connection (Power mode):
Rated Voltage:	12V
Starting Voltage:	<=9.0V
Power Consumption:	3.6W
Rated Current:	0.30A
Speed:	1500 RPM+-10%
Air Flow:	82.6 CMF
Air Pressure:	1.273 mm-H2O
Noise:	26.5dBA
Weight:	117.9g
MTBF:	100000 hours
Connect with Voltage Reduction Cable (Silence mode)
Rated Voltage:	(To FAN)7V
Starting Voltage:	<=7.0V
Power Consumption:	1.56W
Rated Current:	0.13A
Speed:	800 RPM+-10%
Speed:	800 RPM+-10%
Air Flow:	32.5 CMF
Air Pressure:	0.305 mm-H2O
Noise:	12.6dBA
Weight:	117.9g
MTBF:	100000 hours

04-29-2012
Reviewer: Ultrasonic2 (7)
Bought 2 of these for my radiators. However when the air flow is restricted they make a Huge amount more nose than un restricted. Even using them as an exhaust fan on my HAF-X, made the fan very loud. I had to space the fan away from the inside of the case by 3mm to reduce the noise. Bottom line they are SOOO much louder than their rating when you put this fan against anything. I dont use them on my rads because of the above. they do however look great.

04-07-2012
Reviewer: Chunkboi (7)
I got this fan at Fry''s to replace the existing fan on my NZXT case (it kept triggering an underspeed alarm on my fan controller). The only thing that was wierd with this product was that I expected the fan to blow air towards the spinny side (the side opposite the motor mount frame). At least the Antec fan had an arrow indicating direction of flow. However, once mounted properly, I have had quiet operation, and no underspeed alarms. On the FP-01 controller in automatic mode, this fan is whisper-quiet at no more than 1140 RPM. Plus the LED shade matches cold cathode lighting I have in place. Wish they''d put the airflow direction on the housing, but...a minor inconvenience for solid results.

08-04-2011
Reviewer: Terb (1)
Added these two fans to my H50''s rad for a push/pull config in the antec 902 case. Idle is about 26c-29c with load around 30c-35c (depending). Prime95 pushes temps low to mid 40''s

06-01-2011
Reviewer: Tex (5)
I use these all over the place, putting 10 of them in a new case to push/pull on dual radiators. Quiet, pretty, and last forever while moving a good amount of air!

02-09-2011
Reviewer: ()
I bought 7 of these fans to put in my Armor A60 case, and when running at 12v they move a ton of air at a very tolerable noise level. I am using a Sunbeam Rheosmart Fan Controller to control these bad boys and to add pwm functionality.