The baybus allows you to control the speed of the fans via a simple switch with three different settings. This allows fans to run at full speed (12v), half speed (7v), or off. With a baybus, you can make all the fans in your case virtually silent while you’re surfing the web or using other low demand applications. At the flip of a switch you can be back at full cooling power for gaming or other heat generating applications. This is ideal for those who want to balance cooling and noise levels with ease.

This is a new revision of the baybus! Custom manufactured by us, the new kit sets a new standard in baybus design.

The 6 port setup lets you control 50% more fans than any other standard baybus available today. The extra 2 switches forced another design change, moving the wire screw downs and the 4 pin power connector to the back of the PCB, which means they're easier to use.

Each switch is rated to a spec of 8W of power, which is 33% higher than the classic 6W for older baybus designs. This means that you have a fair bit more overhead for hooking up a more powerful fan/more fans.

• 6 independant fan channels
• Bi-Color LED on each switch (High- red, low- blue, Off- off)
• 8W per channel, pre-production units tested stable and safe at 14W on each channel at once, for a total power consumption of 84W across the baybus.
• Easy Access screw down terminals located on the rear of the PCB instead of the front.
• 4-pin power supply connection also located on rear of PCB for easier access.
• Pot located at top of unit (one for each switch) for adjusting the low voltage level. Adjusts from 7-9V (Higher voltages are required for fans such as sunons that won't run at 7volts)
• There's the hard stats on the hardware itself, now here's what you'll get when you see one:
• The baybus PCB which comes with all 6 switches and LEDs pre-installed.
• A lexan drill template for the 5 1/4" bay cover (already has adhesive installed on the plate for mounting)
• 6 LED clip holders for the LED holes
• Detailed instructions explaining installation and setup

09-30-2011
Reviewer: Bzzeigler (3)
I ordered this for my Corsair 800D, premounted in the Lian Li bay cover. Simply put, I wasted $22 having it installed in this bay cover. They neglected to mention ANYWHERE on both this page, and the Lian Li 5.25" Bay Cover pages (both black and silver) that these will only mount in a Lian Li case. I haven''t even bothered trying out the controller as I have to first devise a method for mounting this in my case.

12-08-2007
Reviewer: Franzkefka (13)
But i guess thats what you get when something is hand made. i recieved mine and a few of the switches werent exactly straight one was higher than the others, not a biggy i bent them back as close as i could, just made the install into a Lian li Front panel a bit tougher. and seccondly. WAY prior to Installing and powering up, between each switch is a Transistor? or resistor?, little flat black chip with 3 legs, pay very good attention to weather or not those are touching the sides of the switches, if they do bend them away very carefully. as it will short the baybus, cause switches to not work properly and electrify your case. after i got all that worked out, this is really an amazing Baybus, i dont expect to replace this one anytime soon. would recommend to someone to buy. and would/will buy again

02-11-2007
Reviewer: ()
I first purchased this about two years ago. Since than, It has performed without a hitch. I do not use all the ports but the LEDs on the ones I do use are still shining brightly. There was a period in between the two years in which I removed it for a couple of months. It got banged around in my drawer, but it worked like the day I bought it when I re-installed it. Can''t go wrong. One downside. Due to the location of my computer the bright LEDs tend to get annoying. I would prefer the device to come without LEDs. The switch position speaks for itself. I don''t need an LED telling me what speed its at.

02-05-2007
Reviewer: ()
Controller works great, I love the layout and ease of use. Good adjustability on low speed voltage. Only nag is 6 months later, almost all of the LEDs have burnt out. :(

01-25-2007
Reviewer: trenchdog (1)
Was looking for a cheap 6 fan control and I found one. Works great, BRIGT leds, Fun toggle switches lol. make sure ur fans are on high if they have a swith control built in or it wont be able to go to high from the switch. Thin, clean controller. I had it preinstalled on the black tray cover, came perfectly installed, no scratches, good deal.

	Twisted Mods.com
	Virtual-Hideout