 |
12-08-2011
 Night and Day
So far i have only installed one of these in my loop which cools an i5 2500k. I meant to install 2 of these but i forgot to purchase an sli bridge, so for now only one is installed. The temperatures dropped dramatically -
gpu 1 air/75-85 water/33-38
gpu 2 air/70-75 water/33-38
obviously it has helped a LOT with my gaming, also both cards are over clocked from 822mhz to 998mhz
hope this helped. |
|
12-08-2011
Night and Day
So far i have only installed one of these in my loop which cools an i5 2500k. I meant to install 2 of these but i forgot to purchase an sli bridge, so for now only one is installed. The temperatures dropped dramatically -
gpu 1 air/75-85 water/33-38
gpu 2 air/70-75 water/33-38
obviously it has helped a LOT with my gaming, also both cards are over clocked from 822mhz to 998mhz
hope this helped. |
 |
12-08-2011
couldnt be happier
just built my first pc and liquid cooled it too, i used this for my CPU and i couldnt be happier. Normally under air my cpu under load would run up to 45c now it stays at 33c steady, even with two other gpu''s being cooled. I live with no A/C and its usually 80 Fahrenheit here so it will most likely be cooler in a cooled house.
note- it didnt fit completely correctly on my evga p67 ftw even with all of the plastic washers and all, the back part of the cpu retention holder just stuck out to much and sorta pushed on the metal bracket. i had to create some plastic washers to give it the necessary lift to keep the bracket from bending my board. |
 |
12-08-2011
 i hate writing bad reviews.
ive never really had to write a bad review but i feel that you all should definitely know whats coming in the box. first, you ALL need to buy better adhesive/velcro from where ever. this stuff does NOT stick and it appears that im not the only with this problem either.. i am constanly having to stick these back in place.
also, the white cables are VERY short and cheap hardly leaving you with room to tidy/manuever the components around in your case to make it neat, i dont know about you but i like my case VERY neat and those cables made it quite tough on my.
the product definitely works fine with no issues and if the above comments do bother you that most likely you will be very satisfied with this product, cheers. |
 |
12-08-2011
 quite satisfied.
These are by far the cheapest compression fittings i could find, and when purchasing 12+ those other fittings prices start to add up. i almost had no difficulty installing these except on my CPU water block, because they were a bit wide they sorta touched and scraped against each other when tightening the last fitting on (sorry if that doesnt make sense)
other than that this product worked like a charm and i ESPECIALLY love how small they were compared to other fitting. |
 |
12-08-2011
 its SORTA uv..
This stuff looks quite nice in the light without UV and is quite clear which is cool but keep in mind its not very UV reflective at all.. not saying that it doesnt have the potential though, all you need to do is install more cathodes and keep them quite close to the tubing.
other that the uv issue all is well, quite a nice bit of tubing and WAY more than enough for multiple loops. |
 |
12-08-2011
a bit thrown off but completely satisfied.
I purchased this product but when it arrived, the box said it was a DP1200 DC Brushless Pump (CPX-PRO) no where on the box did it say ''danger den'' but thats the only thing that threw me off... just weird is all..
Actual review-
The pump is actaully quite amazing, its COMPLETELY silent unless you stick your head in hte case and put your head to the unit.. (i actually did) it pumps quite a large amount of water for how small the unit and price was. I would DEFINITELY recommend this product to anyone, there is just no point in spending all of the extra money on the other pumps THIS THING IS PERFECT. |
 |
12-08-2011
works perfectly.
The product is quite heavy and large which sorta threw me off but still NO problems installing. Id like you all to keep in mind that the in/out ports are right next to each other and there are NO other ports on the other side. this works out quite nicely if you have a bay resevoir (i do) to go right below it. I do wish it had ports on both sides though, i ignorantly assumed it did for some reason i cannot explain which made me redesign my loop a bit when it arrived but still, VERY satisfied with the quality. |
 |
12-08-2011
Looks amazing, but will require some work.
This bay will NOT fit into most new cases without a bit of work. The retention flaps in each slot that your spin bay occupies will need to be bent for this to fit at all. My HAF 932 is QUITE sturdy and put up quite a fight with this install... either way it worked eventually and now all is great. would definitely recommend this product to others. |
3471 fans like us!
About Us
Site Map
Shop by Brand
Liquid Cooling
