 |
03-01-2012
 Best compression fittings ive ever tried
The ability to tighten with a tool is genius. Just mke sure to apply to your reservoir before you bolt it down to your case or else itll take a lot longer. Also this thing is great for changing liquids as it can be taken off just as easliy as put on |
|
03-01-2012
Best compression fittings ive ever tried
The ability to tighten with a tool is genius. Just mke sure to apply to your reservoir before you bolt it down to your case or else itll take a lot longer. Also this thing is great for changing liquids as it can be taken off just as easliy as its put on. |
 |
03-01-2012
Half as loud as my Asus fans
I love the Scythe brand. These fans pump Huge amount of air even at half or even at quarter power. Ive got two of these on my server and just love how much cooler my server is with my H70 Corsair recieving fresh air from these fans. Great Price too. |
 |
03-01-2012
Powerful even at low speeds
Other than the fact that this fan looks super cool, it also blows air like a champ. A little noisy at full blast but whatever youll you need this fan will do it. Also comes with a 7v cable, screws and also four rubber anti rattle screw things. Great buy! |
 |
03-01-2012
Great Radiator
I have two of these in my super modded computer. I took my case and a server case cut holes in them to allow me to put my pump, radiator and drain "externally" in my server case.Dropped my temps from 70+ from air to averaging 45 degrees Celsius under heavy gaming! Ive got Two Way SLI GTX 580 and my 2600K OC''ed to 4.5 with the temps normally around 35 cel. |
 |
03-01-2012
Darker than others but thats what i wanted
This liquid is really purple and easily stains to allow you to see if its leaking. I love the tip that allows you to cut more for a bigger hole or less for a smaller hole. |
 |
03-01-2012
Used on three different boards and it worked with all them. no modding
I''ve had an x58 sabertooth and two way sli gtx 580 and it worked fine. than upgraded to p8z68-v pro gen3, no modding. than finally to asrock extreme 7 gen3 that allows three way sli and or 16x-16x for two way sli instead of other boards offering 8x-8x for two way, no modding of the tubes. The only thing is that when your removing your video cards from the mobo be sure you don''t pull the cards apart from each other too much or liquid will spill out from the tubes and fitting. Other than that Excellent and cheap buy! |
 |
03-01-2012
Love these barbs
These barbs are much better than the colored ones. With time the colored ones, especially black barbs will peel off paint and become rusty. These on the other hand are, as i believe to be thicker if no fully chrome. Wouldnt use any barb without clamps though, which is why i prefer compression fittings but these things are really good and cheap. |
 |
03-01-2012
 Good but also peel off and rust
These barbs are really nice looking and get the job done, except for the fact the paint comes off and it rusts, leaving a little bit of residue in your water system. Other than that I would recommend to people. Could just use a sponge cube or something similar to trap it. |
 |
03-01-2012
Great
I bought two of these to create a dual loop in my system. One loop goes to the cpu and than into the y block and other goes to my Two Way SLI GTX 580 loop than into the same y block. Than they go to my pump, head to my dual radiators, than back into the other y block that splits into the first loop reservoir, and towards the second loop reservoir. I cant say for sure, since ive never seen my system before these y block splitters were implemented, but im sure its allows for a much cooler system. |
3471 fans like us!
About Us
Site Map
Shop by Brand
Liquid Cooling
